HAU-MIC-AWM2

Marmitek AWM2 Micromodule (X-10 Micromodules)
Transmitter for 2 addresses with built-in appliance module.
 

Features

• Extremely small size (46x46mm and only 16 mm thick)

• Built-in appliance module with 16A rating

• Relay holds last state on power loss

• Low noise relay

• Two-way X-10 communication

• Able to change internal ON/OFF state by global commands like ALL LIGHTS ON and ALL UNITS OFF to stay in "sync" with modules to which it is configured

• HouseCode, UnitCode and settings can be simply programmed with every X-10 compatible controller (e.g. Marmitek 8in1 in combination with TM13 transceiver), except for the CM11 computer interface

• Improved S/N ratio for reliable X-10 communication

• Power/Status/Configuration LED

The AWM2 MicroModule is an extremely small Marmitek X10 Transmitter for 2 addresses with built-in appliance module. The AWM2 connects up to 2 momentary or maintained switches by wire leads. External switch 1 (connected to the brown and blue wire) controls the relay and transmits ON/OFF X-10 command for the configured address. Switch 2 (connected to the red and blue wire) only transmits an ON/OFF command for the configured address plus one. MicroModule AWM2 uses 2-way X-10 communication. Marmitek MicroModules are designed to fit in the rear of European junction boxes, behind any installed switch or outlet.

Applications

• Remote ON/OFF control of electrical loads

• Provides powerline carrier control to existing light switches

• Transforms conventional switches into an X-10 transmitter

• Full control of all your X-10 modules by conventional switches

• Choose your own brand, design and color for switches and wall sockets

• Place X-10 modules out of sight

• Turn every existing wall socket into an X-10 controlled wall socket

• Ideal for installation into light fixtures, home appliances and other limited areas

• Install two-way switches without any additional wiring between switches (Marmitek MicroModules transmit their status to other MicroModules through the power line).

• Use a conventional switch on a fixed location to execute Macro's

 Download the Illustrative brochure.

 Download the Comparative table of X-10 Micromodules.

 Download the Multilingual Manual of this product.

Download the content by clicking on the title. If you've not installed Adobe Reader, please click on the logo below.

EUR 79,00

Technical info:

• Supply voltage: 230 V +10% -15% 50 Hz

• Supply current : < 20 mA capacitive

• Making capacity: 2000 W ( incandescent lamp) 3 A (motors) 16 A (resistive loads)

• Signal sensitivity: 15 mVpp min 50 mVpp max at 120 kHz

• Input impedance: 180 Ohms (L - N) at 120 kHz

• Connections: screw type terminals for phase, neutral and switched phase, wire for switch connection

• Dimensions: 46 x 46 x 17 mm

Availability:  5 business days

HAU-MIC-AW12

Marmitek AW12 In wall appliance module (X-10 Micromodules)
Small enough to fit behind a standard wall switch.
 

Features
The AW12 Micro Module can be mounted behind any standard wall switch. It is an X10 receiver module that can be controlled by any X10 controller or remote control sending X10 signals. The internal relay can also be tripped by external latched or momentary action wall switches. The AW12 reacts to the standard X10 commands like: "ALL UNITS ON", "ALL UNITS OFF", "ALL LIGHTS OFF" from any X10 controller set to its "House Code" regardless of "Unit Code" or alternatively individual unit control by "ON", "OFF". "House Code" and "Unit Code" are programmed using any X10 compatible controller. There is an E²PROM that stores the "House Code" and "Unit Code" even during blackouts.

Applications
The unit will accept either momentary switches or a standard wall switch. If a momentary switch is used, the relay changes state each time the key is pressed, as long as the key-press lasts for less than 1.75 seconds. If a standard wall switch with latching action is used, it is assumed the keypress will last for more than 1.75 seconds. In this case the relay changes state on both the closure and release.

 Download the Illustrative brochure.

 Download the Comparative table of X-10 Micromodules.

 Download the Multilingual Manual of this product.

Download the content by clicking on the title. If you've not installed Adobe Reader, please click on the logo below.

EUR 49,00

Availability:  5 business days

HAU-MIC-TMA4

Marmitek TMA4 Micromodule (X-10 Micromodules)
Transmitter for 4 addresses and the commands ON and OFF.
 

Features

• Extremely small size (46x46mm and only 16 mm thick)

• Two-way X-10 communication

• Transmits ON when contacts are opened, transmits OFF when contacts are closed

• HouseCode, UnitCode and settings can be simply programmed with every X-10 compatible controller (e.g. Marmitek 8in1 in combination with TM13 transceiver). Except with the CM11 computer interface

• Improved S/N ratio for reliable X-10 communication

• Power/Status/Configuration LED

The TMA4 MicroModule is an extreme small Marmitek X10 Transmitter for 4 addresses and the commands ON and OFF. The TMA4 accepts up to four maintained switches by wire leads and transmits up to four sequential X-10 powerline carrier ON/OFF addresses. MicroModule TMA4 uses 2-way X-10 communication. Marmitek MicroModules are designed to fit in the rear of European junction boxes, behind any installed switch or outlet.

Applications

• Remote ON/OFF control of electrical loads

• Combine your Marmitek X-10 system with sensors, alarm outputs, etc. by hooking up to NO (normally open, open=OFF, close=ON) output contacts

• Transforms conventional switches into an X-10 transmitter

• Provides powerline carrier control to existing light switches

• Transforms conventional switches into an X-10 transmitter

• Full control of all your X-10 modules by conventional switches

• Choose your own brand, design and color for switches and wall sockets

• Place X-10 modules out of sight

• Turn every existing wall socket into an X-10 controlled wall socket

• Ideal for installation into light fixtures, home appliances and other limited areas

• Install two-way switches without any additional wiring between switches (Marmitek MicroModules transmit their status to other MicroModules through the power line).

• Use a conventional switch on a fixed location to execute Macro's

 Download the Illustrative brochure.

 Download the Comparative table of X-10 Micromodules.

 Download the Multilingual Manual of this product.

Download the content by clicking on the title. If you've not installed Adobe Reader, please click on the logo below.

EUR 79,00

Technical info:

• Extremely small size (46x46mm and only 16 mm thick)

• Two-way X-10 communication

• Transmits ON when contacts are opened, transmits OFF when contacts are closed

• HouseCode, UnitCode and settings can be simply programmed with every X-10 compatible controller (e.g. Marmitek 8in1 in combination with TM13 transceiver)

• Power/Status/Configuration LED

Availability:  5 business days

HAU-MIC-TMD4

Marmitek TMD4 Micromodule (X-10 Micromodules)
Transmitter for four addresses and the commands DIM/BRIGHT and ON/OFF.
 

Features

• Extremely small size (46x46mm and only 16 mm thick)

• Two-way X-10 communication

• Able to change internal ON/OFF state by global commands like ALL LIGHTS ON and ALL UNITS OFF to stay in "sync" with modules to which it is configured

• HouseCode, UnitCode and settings can be simply programmed with every X-10 compatible controller (e.g. Marmitek 8in1 in combination with TM13 transceiver), except for the CM11 computer interface

• Improved S/N ratio for reliable X-10 communication

• Power/Status/Configuration LED

The TMD4 MicroModule is an extreme small Marmitek X10 Transmitter for 4 addresses and the commands DIM/BRIGHT and ON/OFF. The TMD4 accepts up to four momentary switches by wire leads and transmits up to four sequential X-10 powerline carrier ON/OFF & DIM/BRIGHT addresses. MicroModule TMD4 uses 2-way X-10 communication. Marmitek MicroModules are designed to fit in the rear of European junction boxes, behind any installed switch or outlet.

Applications

• Remote ON/OFF and DIM/BRIGHT control of lighting

• Provides powerline carrier control to existing light switches

• Transforms conventional switches into an X-10 transmitter

• Full control of all your X-10 LAMP modules by conventional switches

• Choose your own brand, design and color for switches and wall sockets

• Place X-10 modules out of sight

• Install two-way switches without any additional wiring between switches (Marmitek MicroModules transmit their status to other MicroModules through the power line).

 Download the Illustrative brochure.

 Download the Comparative table of X-10 Micromodules.

 Download the Multilingual Manual of this product.

Download the content by clicking on the title. If you've not installed Adobe Reader, please click on the logo below.

EUR 79,00

Technical info:

• Extremely small size (46x46mm and only 16mm thick)

• Two-way X-10 communication

• Ability to change internal ON/OFF state by global commands such as ALL LIGHTS ON and ALL UNITS OFF allowing the TMD4 to stay synchronised with receivers (addresses) to which it is configured

• HouseCode, UnitCode, and settings can be simply programmed with every X-10 compatible controller (e.g. Marmitek 8in1 in combination with TM13 transceiver)

• Power/Status/Configuration LED

Availability:  5 business days

HAU-MIC-LWM1

Marmitek LWM1 Micromodule (X-10 Micromodules)
Built-in dimmer module, small enough to fit behind any conventional wall switch!
 

Features

• Local control via the switch attached to the module or remote control using Marmitek X-10

• Built-in dimmer, 250W

• Two-way X-10: transmits the set dimmer level to other LWM1, LD11 and LW11 modules (set to the same HouseCode and UnitCode)

• Softstart and softdim

• Memory function for last dimmer setting

• Responds to ON, OFF, DIM, BRIGHTER and extended X-10 (dimmer setting originates from other LWM1 modules)

• Can respond to All Lights On and All Off (configuration)

• Choose between 1-face momentary switch or 2-face momentary switch

Applications
The LWM1 MicroModule can be installed behind conventional wall switches or into wall outlets because of the extreme small size of the MicroModule (Minimum built-in depth 40 mm, advised 50 mm). The MicroModule is also ideal for installation into light fixtures or for use in areas with limited space such as rooms with lowered ceilings. Two different installations: 1-face momentary switch or 2-fase momentary switch.
1-face momentary switch
Spring-back switch without intermediate setting. 1 short press is ON, keeping the button pressed is DIM, second press is OFF. When connecting this type of switch, the brown and red wires are connected. The blue wire is connected to the P or L contact of the switch.
Colour coding for the 1-face momentary switch:
Connect Red and Brown: alternating ON/BRIGHTER and OFF/DIM.
Blue: "COMMON".
2-face momentary switch
Spring-back switch with intermediate setting. Both the top and bottom part of the switch can be pressed. Short press top is ON, long press top is BRIGHTER. Short press bottom is OFF, long press bottom is DIM. When connecting this type of switch, the brown wire is connected to the contact for the top part of the switch (ON/BRIGHTER) and the red wire to the contact for the bottom part of the switch (OFF/DIM). The blue wire is connected to the common P or L contact of the switch.
Colour coding for the 2-face momentary switch:
Brown: ON/BRIGHTER
Red: OFF/DIM
Blue: "COMMON"

 Download the Illustrative brochure.

 Download the Comparative table of X-10 Micromodules.

 Download the Multilingual Manual of this product.

Download the content by clicking on the title. If you've not installed Adobe Reader, please click on the logo below.

EUR 79,00

Note:

• NEVER CONNECT A COILED TRANSFORMER TO THE LWM1 WHILE THE MAIN MASTER SWITCH IS STILL TURNED ON. THE INTERNAL FUSE CAN BLOW.

• To install the MicroModule LWM1 the following wiring is required at the module installation point.
  Neutral
  Phase 230V
  Load. This wire runs directly to the load.

• In the standard setting the LWM1 module assumes a ‘2-face momentary switch’ has been connected.

• Usage of the MicroModules in a 3 phase installation. The X10 transmitters of the MicroModules transmit the command only once for use in the phase of which they are connected. When you want to receive the commands on your other phases as well, you will need to install the CAT3000 phase coupler/repeater.

Availability:  in stock

HAU-MIC-LW12

Marmitek LW12 Micromodule (X-10 Micromodules)
In-Wall Lamp Module.
 

Features

• Makes your X10 System invisible

• Dimmer (60W - 250W)

• Remote and local control On, Off and Dim

• Memory function for last dimmer setting Softstart and softdim

Applications
The LW12 can be controlled with X10 signals via the mains or a momentary switch connected to the LW12. The LW12 has a memory setting for the last dimmer setting and uses SoftStart and SoftDim. The LW12 is the only X10 module that doesn't uses a zero wire. This means it can replace a switch without having to use any extra wiring.

This module can be activated using a momentary switch connected to it or by using Marmitek X-10 PLC signals. It can be operated using the following Marmitek X-10 signals: ON, Off, DIM, BRIGHT and the optional Marmitek X10 commands All Lights On/All Lights Off/All Units Off if these are programmed. The unit will accept a momentary switch. The input for the switch is connected to the phase (brown wire, 230V), the output of the switch is connected to input "K" of the LW12 Micromodule. No Neutral (blue wire) has to be connected to the LW12 MicroModule, which means it can be easily used instead of a normal switch, without having to use any wires. The module is equipped with softstart, softdim and a memory setting for the last dim level.

 Download the Illustrative brochure.

 Download the Comparative table of X-10 Micromodules.

 Download the Multilingual Manual of this product.

Download the content by clicking on the title. If you've not installed Adobe Reader, please click on the logo below.

EUR 49,00

Technical information:

• Supply voltage: 230 V +10% -15%, 50 Hz

• Supply current: <5,5 mA.

• Dimensions: 46 x 46 x 17 (h x w x d)

• Installation: We advise using 50mm deep wall boxes

• Capacity: 60W to 250W. Tungsten and halogen lighting (230V and halogen on low voltage).

• Minimal load: 60W

Availability:  5 business days

HAU-MIC-SWM1P

Marmitek SWM1P In Wall Shutter / Sunblind Switch (X-10 Micromodules)
Operate your electric sun blinds, roll down shutters, etc. remotely and/or locally.
 

Features

• Micromodule with built-in relay with two contacts for connecting a 230V motor.

• Can be controlled remotely with every X10 signal (also simultaneously multiple modules). Of course local operation also remains possible.

• Invisible installation behind existing switches or wall outlets. Brand and model of the momentary switch can be chosen freely so the SWM1P can be used in every interior and installation.

• Equipped with a preset function; a position for rolling down shutters (for instance a day-/ventilation position) which can be pre-set.

• Local blocking position for blocking the motor during for instance cleaning of the windows or maintenance.

• Lowers, in combination with the CM15Pro computer interface, the sun blinds automatically during the day in places where the sun shines inside. This way you protect your furniture against the sunlight, keep the house cool and simulate that you are at home.

• Quick and easy to install and to program.

Applications

• Sunblind micromodule for installation behind a momentary switch or in a junction box.

• Driving of one 230Vac motor with at most 2.5 A.

• Reacts to ON, OFF, DIM+, DIM- and extended sunblind commands.

• One free programmable address A1...P16 for operation.

• One free programmable address A1...P16 for the Preset mode.

• Preset function for programming of a preference position.

• Possibility for controlling multiple SWM1P modules at once to one preference position using the Preset function.

• Local lock function for inhibiting the operation of the motor, for instance during maintenance.

 Download the Illustrative brochure.

 Download the Multilingual Manual of this product.

Download the content by clicking on the title. If you've not installed Adobe Reader, please click on the logo below.

EUR 98,00

Technical information:

• Voltage: 230 V AC+/- 10%, 50 Hz

• Switching capacity: 500W/230 VAC with temperature and mounting restrictions.

• Protection: Continuous driving time maximum 4 minutes.

• Output temperature protected.

• Use: < 1 W

• Fuse: Radial lead micro fuse, 4 AT.

• Power consumption: < 30 mA capacitive

• Signal transmission: > 5 Vpp at 120 kHz

• X-10 transmission: 1 pulse at 0° and 180°

• Signal sensitivity: 5 mVpp...6 Vpp at 120 kHz ± 4 kHz

• Signal to noise ratio: 1.35 : 1

• X-10 Key codes transmitting: ON, OFF, extended

• X-10 Key codes receiving: ON, OFF, DIM+, DIM-, extended, Status Request

• Connection range: Up to 2.5 mm2, tightening moment 0.5 Nm

• Ambient temperature: 0 °C to 35 °C

• Relative humidity (non condensing): 30 to 90%

• Dimensions (LxWxH): 46x46x16mm.

Availability:  5 business days