08070-MIC-LMM31


Haibrain 08070 LMM31 Micromodule (X-10 Micromodules)

Lamp-/dimmer module, MicroModule, ON / OFF / DIM.
  • Suitable for 230V and low-voltage lighting with a transformer, including halogen lighting.
  • Remote control via the mains using Haibrain X-10 Commands and with one or more momentary switches.
  • Switches and dims lighting circuits up to 300W.
  • Can be used in combination with ‘designer’ switching material.
  • Soft start and smooth dimming features, remembers the last dim setting.
  • Makes your X-10 system invisible.
  • Can be regulated from 0% lighting to the desired dim setting.
  • The module is not suitable for dimming and controlling low-energy light bulbs and tube lighting. An Appliance module should be used for these devices.
  • Phase and Neutral have to be available before the module can be installed.
  • Small enough (43.25*47*18.9mm) to fit into a wall box behind a standard wall switch.

Item #: 08070-MIC-LMM31

Availability: in stock



EUR 49,95






Album 

Details

The LMM31 MicroModule is an extremely small Haibrain X-10 dimmer module which can be fitted behind any installed switch or outlet. The lights connected to the MicroModule can be controlled by the Haibrain X-10 system. You will be able to use your switch in the normal way. The LMM31 MicroModule uses one-way X-10 communication.

Specs

TECHNICAL DATA
  • Supply voltage: 230VAC +10% -10% 50 Hz
  • Power Consumption < 1W
  • Making capacity: 300W for inductive/capacitive load
  • Control Load QTY: One
  • Dimmable: Yes
  • Signal sensitivity: better than 25 mVpp at 120 kHz
  • X-10 Key codes to respond to: All units Off, All Lights On, On, Off, DIM, BRIGHT, Extended Dim
  • Input switch: 1- way standard rocker switch (ON/OFF), 1-way momentary switch (normally open contact) (ON/OFF/DIM)
  • Use in 3 phase installation: FD10 (3x) or FKX40 necessary
  • Connections: Wire for a standard rocker switch or momentary switch and connecting clamps for phase, neutral and switched phase.
  • Connection range: Up to 2,5 mm2
  • Control lines: not more than 1 meter between the micro module and the switch
  • Ambient temperature: -10°C tot +50°C (Operation)
  • Weight: 45 gram
  • Dimensions: 43.25mm x 47mm x 21mm

Warning

WARNING: Please install the product by properly connecting PHASE and NEUTRAL wires, after CAREFULLY reading the user manual.

Anything left?

WARNING: programming the micromodules involves sending X-10 commands and/or functions. The easiest method uses the MicroModules Programming Kit.

FAQ

Contacts

 
08074-MIC-LMM32


Haibrain 08074 LMM32 Micromodule (X-10 Micromodules)

Lamp-/dimmer module, MicroModule, ON / OFF / DIM, 2 load.
  • Suitable for 230V and low-voltage lighting with a transformer, including halogen lighting.
  • Remote control via the mains using Haibrain X-10 Commands and with one or more momentary switches.
  • Switches and dims lighting circuits up to a total of 400W.
  • Can be used in combination with ‘designer’ switching material.
  • Soft start and smooth dimming features, remembers the last dim setting. Makes your X-10 system invisible.
  • Can be regulated from 0% lighting to the desired dim setting.
  • The module is not suitable for dimming and controlling low-energy light bulbs and tube lighting. An Appliance module should be used for these devices.
  • Control Load QTY: Two
  • Phase and Neutral have to be available before the module can be installed.
  • Small enough (43.25*47*21mm) to fit into a wall box behind a standard wall switch.

Item #: 08074-MIC-LMM32

Availability: in stock



EUR 49,95






Album 

Details

The LMM32 MicroModule is an extremely small Haibrain X-10 dimmer module which can be fitted behind any installed switch or outlet. The lights connected to the MicroModule can be controlled by the Haibrain X-10 system. You will be able to use your switch in the normal way. The LMM32 MicroModule uses one-way X-10 communication.

Specs

TECHNICAL DATA
  • Supply voltage: 230VAC +10% -10% 50 Hz
  • Power Consumption < 1W
  • Making capacity: <400W in total for incandescent and halogen lighting
  • Control Load QTY: two (1 Yellow / Red, 2 Green / Blue)
  • Dimmable: Yes
  • Signal sensitivity: better than 25 mVpp at 120 kHz
  • X-10 Key codes to respond to: All units Off, All Lights On, On, Off, DIM, BRIGHT, Extended Dim
  • Input switch: 1- way standard rocker switch (ON/OFF), 1-way momentary switch (normally open contact)(ON/OFF/DIM)
  • Use in 3 phase installation: FD10 (3x) or FKX40 necessary
  • Connections: Wire for a double standard rocker switch or momentary switch and connecting clamps for phase, neutral and switched phases.
  • Control lines: not more than 1 meter between the micro module and the switch
  • Ambient temperature: -10°C tot +50°C (Operation)
  • Dimensions: 43.25mm x 47mm x 21mm

Warning

WARNING: Please install the product by properly connecting PHASE and NEUTRAL wires, after CAREFULLY reading the user manual.

Anything left?

WARNING: programming the micromodules involves sending X-10 commands and/or functions. The easiest method uses the MicroModules Programming Kit.

FAQ

Contacts

 
08066-MIC-AMM32


Haibrain 08066 AMM32 In wall appliance module (X-10 Micromodules)

Two-Load Appliance Micro Module.
  • Switch module to turn 230V appliances, halogen and tube lights, etc. On or Off.
  • Can be used in combination with ‘designer’ switching material.
  • Operation of the unit with Haibrain X-10 Commands takes place via the mains wires, which means no extra wiring is necessary.
  • Controllable from a distance with the Haibrain X-10 commands On/Off.
  • Makes your X-10 system invisible.
  • Transforms your existing switch into a X-10 controllable switch.
  • Remote and local control On and Off.
  • Can also be used with low-energy lamps.
  • Quick and easy to install and program.
  • Control Load QTY: Two

Item #: 08066-MIC-AMM32

Availability: out of stock



EUR 79,00






Album 

Details

The AMM32 MicroModule is an extremely small Haibrain X-10 appliance module which can be fitted behind any installed switch or outlet. The lights and appliances connected to this MicroModule can be controlled by the Haibrain X-10 system. You will be able to use your switch in the normal way. This MicroModule uses one-way X-10 communication.

Specs

TECHNICAL DATA
  • Supply voltage: 230Vac ±10% 50Hz
  • Power consumption: < 1W
  • Making capacity:
    • 1800W for resistive (Ohm) load
    • 300W for inductive/capacitive load
    • 1100W for light bulbs and halogen lighting
  • Control Load QTY: Two
  • Dimmable: No
  • Signal sensitivity: better than 25 mVpp at 120 kHz
  • X-10 Key codes to respond to: All Units Off, All Lights On, On, Off
  • X-10 All Lights On by set: Yes
  • Input switch: Double 1-way standard rocker switch
  • Silent relais: Yes
  • Use in 3-phase installation: FD10 (3x) or FKX40 necessary
  • Connections: Wire for a double standard rocker switch and connecting clamps for phase, neutral and switched phase.
  • Control lines: Not more than 1 meter between the micromodule and the switch
  • Ambient temperature: from -10°C to +50°C (operation)
  • Dimensions: 43x47x19mm3 (Specifications may be modified without prior notice)

Warning

WARNING: Please install the product by properly connecting PHASE and NEUTRAL wires, after CAREFULLY reading the user manual.

Anything left?

WARNING: programming the micromodules involves sending X-10 commands and/or functions. The easiest method uses the MicroModules Programming Kit.

FAQ

Contacts

 
08086-MIC-LMM21


Haibrain 08086 LMM21 Micromodule (X-10 Micromodules)

Lamp-/dimmer module, MicroModule, ON / OFF / DIM, 1 load.
  • Suitable for 230V incandescent and (Eco) halogen lighting.
  • Remote control via the mains using Haibrain X-10 Commands and with one or more momentary switches.
  • Switches and dims lighting circuits up to 300W.
  • Can be used in combination with ‘designer’ switching material.
  • Soft start and smooth dimming features, remembers the last dim setting.
  • Makes your X-10 system invisible.
  • No extra wires required for installation.
  • Dimmer (60W - 300W).
  • Can be regulated from 0% lighting to the desired dim setting.
  • Transforms your existing switch into a X-10 controllable switch.
  • Transforms a momentary action switch into an X-10 controllable switch.
  • The module is not suitable for dimming and controlling low-energy light bulbs and tube lighting. An Appliance module should be used for these devices.

Item #: 08086-MIC-LMM21

Availability: out of stock



EUR 44,90






Album 

Details

The LMM21 MicroModule is an extremely small Haibrain X-10 dimmer module which can be fitted behind any installed switch or outlet. The lights connected to the MicroModule can be controlled by the Haibrain X-10 system. You will be able to use your switch in the normal way. The LMM21 MicroModule uses one-way X-10 communication.

Specs

TECHNICAL DATA
  • Supply voltage: 230VAC +10% -10% 50 Hz
  • Power Consumption < 1W
  • Making capacity: 60W/230V to 300W/230V for incandescent lamps and Eco halogen light
  • Control Load QTY: One
  • Dimmable: Yes
  • Signal sensitivity: better than 25 mVpp at 120 kHz
  • X-10 Key codes to respond to: All units Off, All Lights On, On, Off, DIM, BRIGHT, Extended Dim
  • Input switch: 1- way standard rocker switch (ON/OFF), 1-way momentary switch (normally open contact) (ON/OFF/DIM)
  • Use in 3 phase installation: FD10 (3x) or FKX40 necessary
  • Connections: Wire for a standard rocker switch or momentary switch and connecting clamps for phase, neutral and switched phase.
  • Connection range: Up to 2,5 mm2
  • Control lines: not more than 1 meter between the micro module and the switch
  • Ambient temperature: -10°C tot +50°C (Operation)
  • Weight: 45 gram
  • Dimensions: 43.25mm x 47mm x 21mm

Warning

WARNING: Please install the product by properly connecting PHASE and NEUTRAL wires, after CAREFULLY reading the user manual.

Anything left?

WARNING: programming the micromodules involves sending X-10 commands and/or functions. The easiest method uses the MicroModules Programming Kit.

FAQ

Contacts

 
08090-MIC-LMM22


Haibrain 08090 LMM22 Micromodule (X-10 Micromodules)

Lamp-/dimmer module, MicroModule, ON / OFF / DIM, 2 load.
  • Suitable for 230V incandescent and (Eco) halogen lighting.
  • Remote control via the mains using Haibrain X-10 Commands and with one or more momentary switches.
  • Switches and dims lighting circuits up to 400W.
  • Can be used in combination with ‘designer’ switching material.
  • Soft start and smooth dimming features, remembers the last dim setting.
  • Makes your X-10 system invisible.
  • No extra wires required for installation.
  • Dimmer (60W - 400W).
  • Can be regulated from 0% lighting to the desired dim setting.
  • Control Load QTY: Two.
  • The module is not suitable for dimming and controlling low-energy light bulbs and tube lighting. An Appliance module should be used for these devices.

Item #: 08090-MIC-LMM22

Availability: Usually ships in 3-4 days



EUR 52,95






Album 

Details

The LMM22 MicroModule is an extremely small Haibrain X-10 dimmer module which can be fitted behind any installed switch or outlet. The lights connected to the MicroModule can be controlled by the Haibrain X-10 system. You will be able to use your switch in the normal way. The LMM22 MicroModule uses one-way X-10 communication.

Specs

TECHNICAL DATA
  • Supply voltage: 230VAC +10% -10% 50 Hz
  • Power Consumption < 1W
  • Making capacity: 60W/230V to 400W/230V in total for incandescent lamps and Eco halogen light
  • Control Load QTY: two (1 Yellow / Red, 2 Green / Blue)
  • Dimmable: Yes
  • Signal sensitivity: better than 25 mVpp at 120 kHz
  • X-10 Key codes to respond to: All units Off, All Lights On, On, Off, DIM, BRIGHT, Extended Dim
  • Input switch: 1- way standard rocker switch (ON/OFF), 1-way momentary switch (normally open contact)
  • Use in 3 phase installation: FD10 (3x) or FKX40 necessary
  • Connections: Wire for a double standard rocker switch or momentary switch and connecting clamps for phase, neutral and switched phase.
  • Control lines: not more than 1 meter between the micro module and the switch
  • Ambient temperature: -10°C tot +50°C (Operation)
  • Dimensions: 43.25mm x 47mm x 21mm

Warning

WARNING: Please install the product by properly connecting PHASE and NEUTRAL wires, after CAREFULLY reading the user manual.

Anything left?

WARNING: programming the micromodules involves sending X-10 commands and/or functions. The easiest method uses the MicroModules Programming Kit.

FAQ

Contacts

 
09806-MIC-AWM2P-SAIX12


Haibrain 09806 AWM2P/SAIX12 Micromodule (X-10 Micromodules)

X-10 transmitter for 2 addresses with a built-in appliance module.
  • Turn your switching system into an X-10 switching system
  • Can also transmit X-10 commands (two-way).
  • Invisible installation behind existing switches or wall outlets. Brand and model of the switch can be chosen freely so the AWM2P/SAIX12 can be used in every interior and installation. The module is also ideal for building in light armatures and for installing in small spaces with for instance lowered ceilings.
  • To this module two switches can be connected. One controls the internal appliance module, but also controls the matching X-10 command through the power line. With the second switch ON/OFF commands can be sent for a second X-10 address.
  • This module is suitable for installing two-way switches without wiring between the switches (MicroModules pass on their status to other MicroModules).
  • The AWM2P/SAIX12 can control Macro's/Scenario's by operating a conventional switch (with for instance Haibrain ActiveHomePro).

Item #: 09806-MIC-AWM2P-SAIX12

Availability: out of stock



EUR 100,00






Album 

Dettagli

Il MicroModulo AWM2P/SAIX12 è un Trasmettitore X-10 Haibrain molto piccolo per 2 indirizzi, con modulo interno per elettrodomestici. AWM2P/SAIX12 consente di collegare fino a 2 interruttori o pulsanti filari. L'interruttore 1 comanda il relé e trasmette i comandi X-10 ON/OFF per l'indirizzo configurato. L'interruttore 2 trasmette solo un comando ON/OFF per l'indirizzo successivo a quello configurato. Il MicroModulo AWM2P/SAIX12 utilizza la comunicazione X-10 bidirezionale. I MicroModuli Haibrain sono progettati per essere inseriti all'interno dei cassetti di derivazione Europei, oppure all'interno dei cassetti per interruttori e prese di corrente, dietro i frutti preesistenti.

Specifiche

CARATTERISTICHE TECNICHE
  • Tensione: 230VAC/50Hz
  • Corrente: 16A
  • Assorbimento: <1W
  • Trasmissione segnale: >5Vpp su 5Ohm a 120kHz in accordo con EN50065-1, EN50065-2-1, EN50065-4-1
  • Sincronizzazione trasmissione: 1 impulso burst a 0°/180°
  • Sensibilità segnale: 25mVpp…6Vpp a 120 kHz ± 4kHz
  • Rapporto S/N: 1.35:1
  • Collegamenti: Fino a 2.5 mm2, coppia di serraggio 0.5 Nm
  • Temperatura ambiente minima: 0°C
  • Temperatura ambiente massima: 40°C
  • Pressione atmosferica: 86 kPa - 106 kPa
  • Umidità relativa (senza condensa): da 30% a 90%

Avviso

ATTENZIONE: effettuare l'installazione del prodotto rispettando i collegamenti di FASE e NEUTRO, dopo aver letto ATTENTAMENTE il manuale d'istruzioni.

Non scordi nulla?

ATTENZIONE: la programmazione dei micromoduli prevede l'invio di comandi e/o funzioni X-10. Il metodo più semplice è quello di utilizzare il Kit Programmazione MicroModuli.

FAQ

Contatti

 
09809-MIC-LWM1P-DAIX12


Haibrain 09809 LWM1P/DAIX12 Micromodule (X-10 Micromodules)

X-10 transmitter for 1 address with built-in dimmer module.
  • Convert a momentary switch into an X-10 controllable switch
  • Switch On, Off and dim remotely and locally.
  • The module is ideally suited to build in light armatures and for installation in small spaces in for instance lowered ceilings.
  • Multi-purpose: fully free choice in brand, colour and model switch material. With the built-in dimmer you can switch and dim 230V light bulbs, 230V halogen lighting and low voltage halogen lighting with electronic transformer suitable for phaseingate up to 120 Watt.
  • Local control via the switch attached to the module or remote control using Haibrain X-10.
  • Softstart and softdim.
  • Memory function for last dimmer setting.
  • Responds to ON, OFF, DIM, BRIGHT and extended X-10 (dimmer setting originates from other modules).
  • Choice between 1-way momentary switch or 2-way momentary switch.
  • Can also transmit X-10 commands (two-way).

Item #: 09809-MIC-LWM1P-DAIX12

Availability: out of stock



EUR 116,95






Album 

Dettagli

LWM1 è un MicroModulo con dimmer interno che può essere installato nei cassetti esistenti, dietro gli attuali pulsanti. LWM1 può essere comandato mediante segnali X-10 sulla linea elettrica oppure mediante pulsanti ad esso collegati. LWM1 è in grado di memorizzare l'ultima impostazione dimmer e utilizza SoftStart e SoftDim. Il livello dimmer di LWM1 è trasmesso sulla rete elettrica ad altri moduli LWM1, LD11 o LW11 (solo se impostati sullo stesso indirizzo).

Specifiche

CARATTERISTICHE TECNICHE
  • Alimentazione: 230VAC/50Hz
  • Potenza: 250W/230V con restrizioni relative alla temperatura e al fissaggio.
    120W/230V Lampade ad incandescenza.
    100W Illuminazione alogena a bassa tensione con trasformatore avvolto.
    120W Illuminazione alogena con trasformatore elettronico Halotronic. (Trasformatore consigliato: Serie Osram HTM. Usando trasformatori diversi, consigliamo di verificare la funzionalità dell’abbinamento prima di montare il sistema.).
    Softstart/Softdim. (Avvio soft / attenuazione soft).
    Memorizzazione del livello dimmer.
  • Codici X-10: All Units Off, All Lights On, On, Off, Dim, Bright, Extended Code 1 tipo 3, Pre-Set Dim, Status Request.
  • Trasmissione X-10: 1 impulso a 0° e 180°.
  • Interruttore utilizzato: Singolo o doppio pulsante.
  • Fuse: Radial lead micro fuse, 1.6AT, 250V.
  • Connection reach: Till 2.5 mm2
  • Environment temperature: -10°C to +35°C (operation); -20°C to +70°C (storage).
  • Dimensions: 46x46x16mm3.

Avviso

ATTENZIONE: effettuare l'installazione del prodotto rispettando i collegamenti di FASE e NEUTRO, dopo aver letto ATTENTAMENTE il manuale d'istruzioni.

Non scordi nulla?

ATTENZIONE: la programmazione dei micromoduli prevede l'invio di comandi e/o funzioni X-10. Il metodo più semplice è quello di utilizzare il Kit Programmazione MicroModuli.

FAQ

Contatti

 
09794-MIC-TWM4-IMX10


Haibrain 09794 TWM4/IMX10 Micromodule (X-10 Micromodules)

X-10 transmitter for 4 addresses and the commands ON/OFF, BRIGHT/DIM.
  • Turn your switching system into an X-10 transmitter
  • Suitable for steering various Haibrain modules with ON, OFF, DIM +, DIM-, All Lights On, All Units Off or All Lights Off commands.
  • The TWM4/IMX10 can also be used for starting programmed macros in, for example, a Haibrain CM15Pro Computer Interface.
  • Can be set to send either ON or OFF commands (fixed mode) or to alternate between ON and OFF commands (alternate mode).
  • As a dimmer interface adjustable for use with single-pole make-contact pulse switches and pulse switches with 2 make-contacts (if necessary with a zero position, multi-switch).
  • Adjustable automatic (two-way communication) status request.
  • Adjustable reception of group commands for status updates in alternate mode.
  • Invisible installation built-in behind existing switches or wall sockets. The TWM4/IMX10 works with all makes and types of switches, which means it can be used in every interior and with all systems.
  • Quick and easy to install and program.

Item #: 09794-MIC-TWM4-IMX10

Availability: out of stock



EUR 81,95






Album 

Dettagli

Il Micromodulo TWM4/IMX10 è un trasmettitore Haibrain X-10 estremamente piccolo per 4 indirizzi, che supporta i comandi X-10 ON/OFF, DIM/BRIGHT. TWM4/IMX10 accetta fino a 4 interruttori/ pulsanti filari e trasmette i comandi ON/OFF, DIM/BRIGHT a un massimo di 4 indirizzi X-10. Il Micromodulo TWM4/IMX10 utilizza la comunicazione X-10 bidirezionale. I MicroModuli Haibrain sono realizzati per essere inseriti all'interno di cassetti di derivazione e cassetti per interruttori, posteriormente a questi ultimi.

Specifiche

CARATTERISTICHE TECNICHE
  • Tensione nominale: 230VAC/50Hz
  • Consumo corrente: < 30 mA capacitivo
  • Trasmissione di segnale: > 5 Vpp con 5 Ohm a 120 kHz
  • Sincronizzazione trasmissione: 1 impulso burst 0°/180°
  • Sensibilità di segnale: 25 mVpp…6 Vpp da 120 kHz ± 4 kHz
  • Rapporto S/N: 1.35:1
  • Invia i codici X-10: ON, OFF, DIM+, DIM-, All Lights ON, All Lights OFF, All Units OFF, extended
  • Riceve i codici X-10: ON, OFF, DIM+, DIM-, extended, Status Request
  • Collegamenti: fino a 2,5 mm2, momento 0,5 Nm
  • Temperatura ambiente: 0°C fino a +35 °C
  • Umidità relativa (senza condensa): da 30% a 90%
  • Dimensioni: 46x46x16mm3
  • Profondità minima scatola ad incasso: 40mm, consigliati 50mm

Avviso

ATTENZIONE! GLI INGRESSI SONO ESCLUSIVAMENTE ADATTI AD INTERRUTTORI LIBERI DA POTENZIALI O CONTATTI <+5V RISPETTO ALLO ZERO.

ATTENZIONE! IL FILO DI INGRESSO BLU DEL TWM4 È INTERNAMENTE COLLEGATO AL MORSETTO NEUTRO! ASSICURARSI DEL CORRETTO COLLEGAMENTO DI FASE E NEUTRO AL MODULO. SE FASE E NEUTRO VENGONO SCAMBIATI, CI SARÀ UNA TENSIONE DI 230V SUI FILI DI INGRESSO DEL MODULO!

ATTENZIONE: effettuare l'installazione del prodotto rispettando i collegamenti di FASE e NEUTRO, dopo aver letto ATTENTAMENTE il manuale d'istruzioni.

Non scordi nulla?

ATTENZIONE: la programmazione dei micromoduli prevede l'invio di comandi e/o funzioni X-10. Il metodo più semplice è quello di utilizzare il Kit Programmazione MicroModuli.

FAQ

Contatti

 
09463-MIC-AW12


Haibrain 09463 AW12 In wall appliance module (X-10 Micromodules)

X-10 transmitter for 1 address with built-in appliance module.
  • Makes your X-10 system invisible
  • Remote and local control On and Off
  • Transforms your existing switch into a X-10 controllable switch

Item #: 09463-MIC-AW12

Availability: out of stock



EUR 74,95






Album 

Dettagli

Il Micromodulo AW12 può essere montato posteriormente all'interruttore, all'interno di un cassetto per interruttore. Esso è un modulo X10 che può essere controllato da qualsiasi controller o telecomando in grado di inviare segnali X-10. Il relé interno può anche essere pilotato da interruttori esterni filari di tipo a scatto o a pulsante. AW12 reagisce ai comandi standard X-10 come: "ALL UNITS ON", "ALL UNITS OFF", "ALL LIGHTS OFF" inviati da un controller X-10 settato sul suo "House Code", indipendentemente dallo "Unit Code". AW12 reagisce anche a comandi X-10 individuali quali: "ON", "OFF". "House Code" e "Unit Code" sono programmabili utilizzando un qualsiasi controller compatibile X-10. La E2PROM interna all'AW12 mantiene le informazioni di "House Code" e "Unit Code" anche durante i blackout di corrente.

Il Micromodulo accetta sia pulsanti sia interruttori standard. Se viene utilizzato un pulsante, il relé cambia stato ogni volta che il pulsante viene premuto per un tempo inferiore a 1.75 secondi. Se invece viene utilizzato un interruttore, si assume che lo stesso sia premuto per un tempo superiore a 1.75 secondi. In questo caso il relé cambia stato sia in chiusura sia in apertura. AW12 utilizza la comunicazione X-10 unidirezionale.

Specifiche

CARATTERISTICHE TECNICHE
  • Tensione di alimentazione: 230V/50Hz
  • Corrente assorbita: < 20 mA capacitativi
  • Capacità di carico: 3600 W/230V per carico Ohmico; 600 W/230V per carico induttivo / capacitativo; 2000 W/230V per lampade ad incandescenza e alogene a bassa tensione con trasformatore.
  • Carico minimo: 3W
  • Sensibilità del segnale: 15 mVpp min, 50mVpp max a 120 kHz
  • Impedenza d’ingresso: > 180 Ohm
  • Connessioni: fili per connessione interruttori o pulsanti e morsetti per Fase, Neutro e Fase commutata
  • Temperatura ambiente: da -10°C a +40°C (in funzione); da -20°C a +70°C (in magazzino)
  • Dimensioni: 46x46x17mm3

Avviso

ATTENZIONE: effettuare l'installazione del prodotto rispettando i collegamenti di FASE e NEUTRO, dopo aver letto ATTENTAMENTE il manuale d'istruzioni.

Non scordi nulla?

ATTENZIONE: la programmazione dei micromoduli prevede l'invio di comandi e/o funzioni X-10. Il metodo più semplice è quello di utilizzare il Kit Programmazione MicroModuli.

FAQ

Contatti

 
09611-MIC-LW12


Haibrain 09611 LW12 Micromodule (X-10 Micromodules)

Switcher for 1 address with built-in dimmer module.
  • LW12 MicroModule with dimmer
  • Makes your X-10 System invisible
  • No extra wires required for installation
  • Dimmer (60W - 250W)
  • Remote and local control On, Off and Dim
  • Memory function for last dimmer setting
  • Softstart and softdim

Item #: 09611-MIC-LW12

Availability: Usually ships in 3-4 days



EUR 62,50






Album 

Details

The LW12 MicroModule has a built-in dimmer that can be installed behind existing switches or wall outlets. The LW12 can be controlled with X-10 signals via the mains or a momentary switch connected to it. The LW12 has a memory setting for the last dimmer setting and uses SoftStart and SoftDim. The LW12 is the only X10 module that doesn't uses a zero wire. This means it can replace a switch without having to use any extra wiring.

Specs

TECHNICAL DATA
  • Supply voltage: 230VAC/50Hz
  • Supply current: < 20 mA capacitive
  • Making capacity: 60W/230V to 250W/230V for incandescent lamps and halogen lights
  • Signal sensitivity: 15 mVpp min 50 mVpp max at 120 kHz
  • Input impedance: > 180 Ohm (L - N) at 120 kHz
  • X-10 Key codes: All units Off, All Lights On, On, Off, Dim, Bright, All Lights Off, extended code 1 type 3
  • Connection: Connecting clamps for phase, switched phase and switch (neutral not required)
  • Ambient temperature: - 10° C to + 40° C (operation) - 20° C to + 70° C (storage)
  • Dimensions: 46x46x17mm3

Warning

WARNING: Please install the product by properly connecting PHASE and NEUTRAL wires, after CAREFULLY reading the user manual.

Anything left?

WARNING: programming the micromodules involves sending X-10 commands and/or functions. The easiest method uses the MicroModules Programming Kit.

FAQ

Contacts

 
08096-MIC-SMM31


Haibrain 08096 SMM31 In Wall Shutter / Sunblind Switch (X-10 Micromodules)

Shutter switch, MicroModule, ON / OFF / DIM.
  • Operate your electric sun blinds, roll down shutters, etc. remotely and/or locally
  • Makes your X-10 system invisible
  • Invisible installation built-in behind existing switches or wall sockets. The module works with all makes and types of switches, which means it can be used in every interior and with all installations.
  • Quick and easy to install and to program.
  • Transforms your existing 1-way standard rocker switch into a X-10 controllable switch.
  • Micromodule with built-in relay with two contacts for connecting a 230V motor.
  • Can be operated remotely with an X10 signal or locally, fully open/closed or on every interim position.
  • Lowers, in combination with the CM15Pro™ computer interface, the sun blinds automatically during the day in places where the sun shines inside. This way you protect your furniture against the sunlight, keep the house cool and simulate that you are at home.
  • The MicroModule uses one-way X-10 communication.

Item #: 08096-MIC-SMM31

Availability: in stock



EUR 65,00






Album 

Details

The SMM31 Micromodule allows a motorized blind to be controlled either manually from a 1-way standard rocker switch connected to the unit, or remotely by serial Haibrain X-10 Powerline messages sent from a suitable controller.
When controlled serially the blind can be made to go to intermediate settings in addition to fully up or fully down with dim and bright commands.

Shutter switch
What are the differences between shutter modules?
FEATURES SW10 SMM31 SW12 SWM1P/ZAX12
Max Inductive/Capacitive load at 230V ± 10%1400W200W700W500W
Number of usable X-10 addresses1112
X-10 communicationOne wayOne wayOne wayTwo way
ModuleBuilt-inMicromodule
Sendable X-10 commandsOn/Off,
Status,
Extended
Receivable X-10 commandsOn/Off,
Dim+/Dim-,
Extended
On/Off, Dim+/Dim-On/Off,
Dim+/Dim-,
Extended
On/Off,
Dim+/Dim-,
Status request,
Extended
MemoryPreset functionPreset function
Local blocking modeNoYes
Load directly connectable to the moduleYes
Silent RelaisYes
Application in 3 phase installationphase coupler requiredactive phase coupler required
Connectable switchesSwitchMomentary switch
Local operationOwn switchOwn wires (not longer than 1 meter)controlled phase (up to 30 meters)
Dimensions (mm)70x70x5443,25x47x18,946x46x16
LED indication power/ programming modeNoYesNoYes
Supply voltage230V ±10% / 50Hz
Consumed power<1W<0,09W

Shutter switch

Specs

TECHNICAL DATA
  • Supply voltage: 230VAC ±10% 50 Hz
  • Power consumption: <1W
  • Maximum load: 200W for motors
  • Control load QTY: One
  • Signal sensitivity: better than 25 mVpp at 120 kHz
  • X-10 Key codes: Off(1), On(2), Dim, Bright
  • Input switch: 1-way standard rocker switch
  • Use in 3-phase installation: FD10 (3x) or FKX40 necessary
  • Connections: wire for a standard rocker switch and connecting clamps for phase, neutral and motor
  • Control lines: not more than 1 meter between the micromodule and the switch
  • In wall junction box: 50mm
  • Ambient temperature: -10°C tot +50°C (Operation)
  • Dimensions: 43,35mm x 47mm x 18,9mm

Warning

WARNING: Please install the product by properly connecting PHASE and NEUTRAL wires, after CAREFULLY reading the user manual.

Anything left?

WARNING: programming the micromodules involves sending X-10 commands and/or functions. The easiest method uses the MicroModules Programming Kit.

FAQ

Contacts

 
09842-MIC-SW12


Haibrain 09842 SW12 In Wall Shutter / Sunblind Switch (X-10 Micromodules)

Shutter switch, MicroModule, ON / OFF / DIM.
  • Operate your electric sun blinds, roll down shutters, etc. remotely and/or locally
  • Makes your X10 system invisible
  • Micromodule with built-in relay with two contacts for connecting a 230V motor.
  • Can be operated remotely with an X10 signal or locally, fully open/closed or on every interim position.
  • Invisible installation behind existing switches or wall outlets. Brand and model of the switch can be chosen freely so the SW12 can be used in every interior and installation.
  • A 2-way momentary switch with 2 normally open contacts can be connected to this module.
  • Lowers, in combination with the CM15Pro™ computer interface, the sun blinds automatically during the day in places where the sun shines inside. This way you protect your furniture against the sunlight, keep the house cool and simulate that you are at home.
  • Quick and easy to install and to program.

Item #: 09842-MIC-SW12

Availability: out of stock



EUR 74,95






Album 

Details

The SW12 Micromodule allows a motorized blind to be controlled either manually from a momentary switch with two normally open contacts connected to the unit, or remotely by serial Haibrain X-10 Powerline messages sent from a suitable controller. When controlled serially the blind can be made to go to intermediate settings in addition to fully up or fully down.
Window parameters, such as Window Size and Current Position, together with the unit's address are set into it by the user when the unit is put into Install Mode and these are stored in permanent memory. This data is retained even through a loss of power.

Shutter switch
What are the differences between shutter modules?
FEATURES SW10 SMM31 SW12 SWM1P/ZAX12
Max Inductive/Capacitive load at 230V ± 10%1400W200W700W500W
Number of usable X-10 addresses1112
X-10 communicationOne wayOne wayOne wayTwo way
ModuleBuilt-inMicromodule
Sendable X-10 commandsOn/Off,
Status,
Extended
Receivable X-10 commandsOn/Off,
Dim+/Dim-,
Extended
On/Off, Dim+/Dim-On/Off,
Dim+/Dim-,
Extended
On/Off,
Dim+/Dim-,
Status request,
Extended
MemoryPreset functionPreset function
Local blocking modeNoYes
Load directly connectable to the moduleYes
Silent RelaisYes
Application in 3 phase installationphase coupler requiredactive phase coupler required
Connectable switchesSwitchMomentary switch
Local operationOwn switchOwn wires (not longer than 1 meter)controlled phase (up to 30 meters)
Dimensions (mm)70x70x5443,25x47x18,946x46x16
LED indication power/ programming modeNoYesNoYes
Supply voltage230V ±10% / 50Hz
Consumed power<1W<0,09W

Shutter switch

Specs

TECHNICAL DATA
  • Supply voltage: 230VAC/50Hz
  • Power Consumption: <1W
  • Maximum Load: 700W/230V for motors
  • Sensitivity to power line signals: 50mV p-pk @ 120 KHz. For signals >50mV AGC is applied
  • X-10 Key codes: On, Off, DIM+, DIM-, extended
  • Terminals: Screw terminals for L, N, UP (relay), DN (relay)
    Wires for UP key (blue) and DOWN (orange)
  • Switch: momentary switch with two normally open contacts
  • In wall junction box: Minimal 40mm, preferred 50mm
  • Ambient temperature: 0°C - 40°C
  • Dimensions: 46x46x17mm3

Warning

WARNING: Please install the product by properly connecting PHASE and NEUTRAL wires, after CAREFULLY reading the user manual.

Anything left?

WARNING: programming the micromodules involves sending X-10 commands and/or functions. The easiest method uses the MicroModules Programming Kit.

FAQ

Contacts

 
09779-MIC-SWM1P-ZAX12


Haibrain 09779 SWM1P/ZAX12 In Wall Shutter / Sunblind Switch (X-10 Micromodules)

Shutter switch, MicroModule, ON / OFF / DIM.
  • Operate your electric sun blinds, roll down shutters, etc. remotely and/or locally
  • Micromodule with built-in relay with two contacts for connecting a 230V motor.
  • Can be controlled remotely with every X-10 signal (also simultaneously multiple modules). Of course local operation also remains possible.
  • Invisible installation behind existing switches or wall outlets. Brand and model of the switch can be chosen freely so the SWM1P can be used in every interior and installation.
  • Equipped with a preset function; a position for rolling down shutters (for instance a day-/ventilation position) which can be pre-set.
  • Local blocking position for blocking the motor during for instance cleaning of the windows or maintenance.
  • Lowers, in combination with the CM15Pro™ computer interface, the sun blinds automatically during the day in places where the sun shines inside. This way you protect your furniture against the sunlight, keep the house cool and simulate that you are at home.
  • Quick and easy to install and to program.

Item #: 09779-MIC-SWM1P-ZAX12

Availability: out of stock



EUR 120,95






Album 

Details

The SWM1P/ZAX12 Micromodule is suited for remotely and locally operating electric sunblinds, roll down shutters, screens and, if desired, curtains. Because of its extremely small size, the module can be installed behind plaster depth switches and wall outlets (minimal depth of wall box 40 mm, recommended 50 mm). Universally applicable: total freedom of choice for brand, colour and style of switches. ATTENTION! Haibrain Micromodules always have to be mounted in a wall- or junction box.
ATTENTION! Input only suited for 230 V live potential!

Shutter switch
What are the differences between shutter modules?
FEATURES SW10 SMM31 SW12 SWM1P/ZAX12
Max Inductive/Capacitive load at 230V ± 10%1400W200W700W500W
Number of usable X-10 addresses1112
X-10 communicationOne wayOne wayOne wayTwo way
ModuleBuilt-inMicromodule
Sendable X-10 commandsOn/Off,
Status,
Extended
Receivable X-10 commandsOn/Off,
Dim+/Dim-,
Extended
On/Off, Dim+/Dim-On/Off,
Dim+/Dim-,
Extended
On/Off,
Dim+/Dim-,
Status request,
Extended
MemoryPreset functionPreset function
Local blocking modeNoYes
Load directly connectable to the moduleYes
Silent RelaisYes
Application in 3 phase installationphase coupler requiredactive phase coupler required
Connectable switchesSwitchMomentary switch
Local operationOwn switchOwn wires (not longer than 1 meter)controlled phase (up to 30 meters)
Dimensions (mm)70x70x5443,25x47x18,946x46x16
LED indication power/ programming modeNoYesNoYes
Supply voltage230V ±10% / 50Hz
Consumed power<1W<0,09W

Shutter switch

Specs

TECHNICAL DATA
  • Voltage: 230VAC/50Hz
  • Switching capacity: 500W/230 VAC with temperature and mounting restrictions.
  • Protection: Continuous driving time maximum 4 minutes.
    Output temperature protected.
  • Use: < 1 W
  • Fuse: Radial lead micro fuse, 4 AT.
  • Power consumption: < 30 mA capacitive
  • Signal transmission: > 5 Vpp in 5 Ohm at 120 kHz
  • X-10 transmission: 1 pulse at 0° and 180°
  • Signal sensitivity: 5 mVpp…6 Vpp at 120 kHz ± 4 kHz
  • Signal to noise ratio: 1.35 : 1
  • X-10 Key codes transmitting: ON, OFF, extended
  • X-10 Key codes receiving: ON, OFF, DIM+, DIM-, extended, Status Request
  • Connection range: Up to 2.5 mm2, tightening moment 0.5 Nm
  • Ambient temperature: 0 °C to 40 °C
  • Relative humidity (non condensing): 30 to 90%
  • Dimensions: 46x46x16mm3

Warning

ATTENTION! The SWM1P has a thermal protection which protects the module and motor against overheating. Combined with an external heat source the thermal protection can be activated at unwanted moments which makes the module temporary unresponsive. Therefore DO NOT MOUNT the SWM1P in a wall box above a radiator or another heat source or in a wall box which is exposed to direct (and intensive) sunlight.

WARNING: Please install the product by properly connecting PHASE and NEUTRAL wires, after CAREFULLY reading the user manual.

Anything left?

WARNING: programming the micromodules involves sending X-10 commands and/or functions. The easiest method uses the MicroModules Programming Kit.

FAQ

Contacts

 
HAU-X10-MMPK


MicroModules Programming Kit (X-10 Micromodules)

MicroModules Programmer, Lite and Professional versions.
  • Control panel for programming X-10 compatible MicroModules.
  • Can be used directly to send X-10 Key Codes (All units off, all lights on, on, off, dim, bright).
  • It can be used to manage all 16 Housecodes (A-P).
  • Two versions available (Lite and Professional).
  • Lite version allows programming an unlimited number of MicroModules (1-8 Unit Codes).
  • Professional version allows programming an unlimited number of MicroModules (1-16 Unit Codes).

Item #: HAU-X10-MMPK

Availability: out of stock



EUR 65,00

MicroModules Programming Kit




 

Details

If you would like to program all kinds of X-10 compatible MicroModules, fast and easy way, then please take a look at the MMPK - MicroModules Programming Kit (v. Lite and Professional).

MicroModules Programming Kit

Unlike most Haibrain X-10 Modules the MicroModules do not have code wheels to change House Codes and Unit Codes. The factory setting for the MicroModules is to address A1 and no response to the optional function All Lights On.

To change the address and the setting for the All Lights On (All Units Off) function, the module needs to be set to the program mode and X-10 Key Codes should be sent (as prescribed in the manual) by using the MicroModules Programming Kit (v. Lite and Professional).

Specs

TECHNICAL DATA
  • Power supply: 230 VAC/50Hz 2 Watt
  • Signal transmission: 2.5 Vpp at 120 kHz ± 1 kHz
  • X-10 Key codes: All units off, all lights on, on, off, dim, bright
  • RF Frequency: 433.92 MHz
  • Ambient temperature: -10°C to +50°C (operation) / -20°C to +70°C (storage)
  • Dimensions: 115x95x30mm

Contacts

 
Shop with confidence :
Courtesy and professionalism
Courtesy and professionalism
Professional assistance
Professional assistance
100% Secure PayPal Certified
100% Secure PayPal Certified
Fast shipping
Fast shipping
Protected by Copyscape Plagiarism Checker - Do not copy content from this page.
Back to TOP