01807552-A10-SVX10


Haibrain 01807552 SVX10 Signal repeater (A10 XanuraHome)

XanuraHome Micro Module.
  • Repeats all Xanura & Haibrain X10 commands
  • To be installed in a junction box
  • Can be used in single phase installations with low Xanura / Haibrain X10 signal levels where equipment filters are not satisfactory.
  • Amplifies Xanura / X10 signals to their maximum value.
  • The signal amplifier amplifies all letter codes as standard.
  • Can be set up to amplify a single or several letter codes.

Item #: 01807552-A10-SVX10

Availability: 3-5 business days



EUR 57,00






 

Details

Built-in module for the single phase amplification of Xanura Haibrain X10 signals. The Xanurahome SVX10 is a signal repeater that forwards reinforced signals in single-phase systems. The LED is ON all the time when in operating mode. The LED flashes when Xanura / X10 signals are received and amplified.
The SVX10 only works if the original signal level in the fuse compartment is at least 100 mV. Each letter code for a building can only be amplified by one signal amplifier.

  • The signal amplifier must be mounted in a junction box or welding box. The signal amplifier must be protected by a 16 A automatic fuse or fuse link.
  • Each letter code for a building can only be amplified by one signal amplifier.
  • Connect the phase and neutral wire to the terminals on the signal amplifier, see Figure 1 of the manual
  • Program the module if it has not already been programmed, or has been programmed incorrectly.

Specs

  • Supply voltage : 230 V, 50 Hz

FAQ

Warning

WARNING: Not to be used in conjunction with the FKX40 Phase Coupler/Repeater!

Contacts

 
01807605-A10-FKX40


Haibrain 01807605 FKX40 Phase Coupler/Repeater (A10 XanuraHome)

XanuraHome Din-Rail module.
  • The phase coupler must be connected to a 16 A 3-phase group

Item #: 01807605-A10-FKX40

Availability: 3-5 business days



EUR 339,00






 

Details

The phase coupler/repeater receives Haibrain X-10 commands and forwards these commands to all phases. All commands are repeated when passing the phase coupler.

Specs

  • Rated voltage : 3-phase, 230 Vac, 50 Hz
  • Total power consumption : < 2 W
  • Signal transmission : > 5 Vpp in 5 Ohm at 120 kHz
    in accordance with EN 50065-1, EN 50065-2-1, EN 50065-4-1
  • Transmission synchronization : 1 pulse burst at 0°/180°
  • Signal sensitivity : 25 mVpp…6 Vpp at 120 kHz ± 4 kHz
  • Signal/noise ratio : 1,35 : 1
  • Connection range : 2.5 mm2 solid
  • Minimum ambient temperature : 0 °C
  • Maximum ambient temperature : 40 °C
  • Atmospheric pressure : 86 hpA - 106 hpA
  • Relative humidity (non condensing) : 30 tot 90%
  • Housing: IP40 according to IEC 60 529
  • Terminal contact: IP20 according to IEC 60 529
  • Colour : RAL 7035

FAQ

Warning

WARNING: Not to be used in conjunction with the SVX10 Signal repeater!

Contacts

 
06004685-A10-RFIX35


Haibrain 06004685 RFIX35 RF Interface (A10 XanuraHome)

XanuraHome RF Interface with RF-secured function.
  • Makes the Haibrain X10 system operable remotely via RF
  • Easy to install
  • Designed as a wall- or ceiling mountable unit or stand-alone use
  • A maximum of 256 addresses can be controlled with one RF interface
  • RF-secured, only signals from registered remote control units are accepted
  • A maximum of eight remote control units can be registered in the RF-secured mode
  • Maximum communication distance: 100 m (open field)
  • Dimensions: 120 x 80 x 30 mm
  • Color: RAL 9001

Item #: 06004685-A10-RFIX35

Availability: 3-5 business days



EUR 139,00






 

Details

The Xanura RFIX35 can be used to receive RF-commands from XanuraHome / X10 remote controls and send them over the power line to switch or dim actuators.

The RF interface is a receiver that converts RF signals originating from the Haibrain X-10 remote control units into Haibrain X-10 commands and subsequently sends them over the lighting circuit.

The RFIX35 makes wireless and remote operation of the Haibrain X10 system possible. The RF interface can be mounted on a junction box or against a distribution box, but can also be mounted against the rear wall of the meter cabinet, if required. The RFIX35 can also be plugged into a wall socket outlet.

Specs

  • Mains voltage : 230 Vac, 50 Hz
  • Max. power consumption : <2 W
  • Ambient temperature : 0 to 40 °C
  • Frequency : 433,92 MHz; X-10 RF (NEC) compatible protocol
  • Max communication distance : 100 m (open field)
  • Protection class : Class II, Double insulated
  • Type of protection : IP 40 with installation on the wall or ceiling - IP 20 with installation on the wall.
  • Standards: IEC 60950
Housing
  • Dimension (H x W x D) : 120 x 80 x 30 mm
  • Color : RAL9001
Power cable
  • Dimension : Length 1.5 m
  • Color : White

FAQ

Contacts

 
01807553-A10-SAX35


Haibrain 01807553 SAX35 Potential free actuator/interface (A10 XanuraHome)

XanuraHome Surface-mounted module.
  • Two inputs and one output (potential free and galvanically separated)
  • Sends ON/OFF commands (max. two addresses)
  • Receives ON/OFF commands and switches the built-in relay contact (max. 5 A, 30 V)
  • Can be incorporated in a group command
  • Automatic status indication possible
  • Status request possible

Item #: 01807553-A10-SAX35

Availability: 3-5 business days



EUR 149,00






 

Details

The SAX35 is a potential free actuator/interface in a surface-mounted housing. The SAX35 can be used to switch appliances of other manufacturers on the basis of an input contact (max. 5A, 30 V a.c./d.c.). Examples include: a doorbell, electronic lock or heating systems (24 V a.c.). The SAX35 can be installed with the appliance to be connected. The SAX35 communicates with the rest of the system via the lighting circuit. Ideal in situations where there are no leads from the appliance to the meter cabinet.

Specs

  • Nominal supply voltage : 230 V, 50Hz
  • Current consumption : <35 mA
  • Input voltage isolation : 3 kV
  • Clearance and creepage distance prim/sec. :> 5 mm
Galvanically separated connections
Secondary connection terminals
  • Input 1 : Binary (high: V+; low: <+1 V )
  • Input 2 : Binary (high: V+; low: <+1 V )
  • Common (V+) : + 5 V … + 25 V, AC or DC
  • Input current : <7,5 mA
  • Relay contact output : potential-free and galvanically separated relay contact, mono stable normally open
  • Relay contact current : <5 A resistive
Voltage
  • Relay contact/inputs : <30 V
  • Standards : EN 60950
  • Signal strength sending :> 5 Vpp in 5 Ohm
  • Signal sensitivity : 15 mVpp min,> 50 mVpp at 120 kHz

FAQ

Contacts

 
01807604-A10-PMIX35


Haibrain 01807604 PMIX35 Programming and Measuring Interface (A10 XanuraHome)

XanuraHome Programming and Measuring Interface.
  • Sending and receiving commands.
  • Measuring the signal level and noise level of incoming messages.
  • Measuring network impedance.
  • Sending messages with quick-selection buttons.
  • Sending messages with two preset macros.
  • Running macros automatically.
  • Sending messages with adjustable transmission levels.
  • Logging of received and sent messages with error analysis.
  • Easily accessible network diagnostic information.
  • Automatic programming of modules at the touch of a button.
  • Network validation measuring method with reporting for the reliable delivery of new installations.
  • Support for the PMIX35 ASCII protocol similar to the CTX15/35 protocol.
  • Support for the CTX15/35 protocol.

Item #: 01807604-A10-PMIX35

Availability: 3-5 business days



EUR 249,00






 

Details

PMIX35 - Programming and Measuring Interface (E plug).

Model: 1807604

The Programming and Measuring Interface from Haibrain® is a power line communication interface designed to support the standard and extended X10 protocols. In addition, the system enables you to examine the lighting circuit, isolate any disturbances with a filter and test installed modules immediately.

Features:

  • Sending and receiving commands
  • Technical problems in installations can be quickly localised and resolved
  • New installation can be tested for reliability
  • Modules can be quickly and easily programmed

The Programming and Measuring Interface is a 230V mains powered system, and is supplied with an E-plug (also available with an U-plug).

PMIX35 - Network analyzer
PMIX35 - Network analyzer

PMIX35 - 10 PLC programmer
PMIX35 - 10 PLC programmer

Specs

TECHNICAL DATA
  • Rated voltage 230 Vac, 50 Hz
  • Total power consumption Max. 2.5 W
  • Signal transmission Adjustable from 0 to 5 Vpp (per 25 mV) in 5 ? at 120 kHz according to EN 50065-1, EN 50065-2-1, EN 50065-4-1
  • Transmission regulation: Transmission level adjusts itself automatically to the power line impedance. The maximum adjustable level is 5 Vpp.
  • Transmission synchronisation 1 pulse burst at 0°/ 30°/ 60°/ 90°/ 120°/ 150° selectable
  • Signal sensitivity: 25 mVpp-6 Vpp at 120 kHz ± 4 kHz
  • Signal/noise ratio 1.35 : 1
  • Minimum ambient temperature 0°C
  • Maximum ambient temperature 40°C (*)
  • Atmospheric pressure 86 pkA - 106 pkA
  • Relative humidity (non condensing) 30 to 90%
  • Standards NEN-EN-IEC 60669-2-1, NEN-EN-IEC 60669-2-2

In order to continue improving the product, INSTEON reserves the right to change specifications and/or designs without prior notice

Kit contents:
  • 1x PMIX35
  • 1x USB cable
  • 1x Cd-rom with: PMIX35 software + PDF userguide (PMIX35) + Quick reference guide

FAQ

Contacts

 
08029-A10-AFX3


Haibrain 08029 AFX3 - Appliance Filter (A10 XanuraHome)

XanuraHome Plugin Module.
  • High end multistage filter module.
  • To prevent Haibrain X-10 lighting network signals from being absorbed by appliances that have a dampening effect on the network signals.
  • Install the appliance filter between the consumer plug and wall socket.

Item #: 08029-A10-AFX3

Availability: out of stock. Replaced by FM10G.



EUR 39,00






 

Details

Some appliances can cause noise. This electrostatic noise can disturb Haibrain X-10 commands going over the power line. Placing an AFX3 Appliance filter between the noise source (i.e. a washing machine) and the power line will filter the noise coming from this device and keeps the power line clean.

The appliance filter can be used for example with a TV, computer and monitor, washing machine, tumble drier, dishwasher, microwave, copier, laser printer, switched supplies, etc.

Specs

  • Supply : 230 V +/- 15% 50Hz
  • Maximum load : 16 A

FAQ

Contacts

 
09806-A10-SAIX12


Haibrain 09806 SAIX12 Switch Actuator/Interface 230V (A10 XanuraHome)

XanuraHome Micro Module.
  • Two 230 V inputs
  • One input for local relay operation and the transmission of the corresponding ON/OFF command.
  • One 230 V input for relay-independent transmission of ON/OFF commands, for example for use as a 230 V interface behind movement sensors.
  • Option of sending alternating ON/OFF commands (toggle).
  • Sparkfree activation and deactivation of loads.
  • A maximum of two freely programmable addresses can be controlled
  • Loads up to 16 A, suitable for resistive, inductive or capacitive loads
  • A two or three way switching circuit can be automated with only one module
  • Can be incorporated in a group command
  • Automatic status indication possible
  • Status retention in the event of the loss and recovery of mains voltage
  • Can be programmed remotely

Item #: 09806-A10-SAIX12

Availability: out of stock



EUR 99,94






 

Details

The SAIX12 is both a switch actuator and an interface equipped with two 230 V inputs. This module must be fitted in junction or distribution boxes and can be used in combination with: Wall sockets, Switches, Retractive switches with one or two normally open contacts, Movement detectors or sensors (e.g. light detector switch) with a 230 V output. The SAIX12 can be used for easy automation of lighting circuits (or appliances) so that they can be switched remotely or manually.

Specs

  • Rated voltage : 230 Vac, 50 Hz
  • Rated current : 16 A
  • Current consumption : < 30 mA capacitive
  • Signal transmission : > 5 Vpp in 5 Ohm at 120 kHz
    in accordance with EN 50065-1, EN 50065-2-1, EN 50065-4-1
  • Transmission synchronization : 1 pulse burst at 0°/180°
  • Signal sensitivity : 25 mVpp…6 Vpp at 120 kHz ± 4 kHz
  • Signal/noise ratio : 1,35 : 1
  • Connection range : Up to 2.5 mm2, tightening torque 0.5 Nm
  • Minimum ambient temperature : 0 °C
  • Maximum ambient temperature : 40 °C
  • Atmospheric pressure : 86 hpA - 106 hpA
  • Relative humidity (non condensing) : 30 tot 90%

FAQ

Contacts

 
09809-A10-DAIX12


Haibrain 09809 DAIX12 Dimming Actuator/Interface 230V (A10 XanuraHome)

XanuraHome Micro Module.
  • One 230 V input
  • 25–250 W lighting load
  • For incandescent lamps and halogen lighting at 230 V and lowvoltage halogen lighting with wound or leading edge electronic transformer.
  • A two or three way dimmimg circuit can be automated with only one module.
  • Can be incorporated in a group command.
  • Memory mode, switches On to the last used dimming position.
  • Status retention in the event of the loss and recovery of mains voltage.
  • Softstart and softdim.
  • Can be programmed remotely.

Item #: 09809-A10-DAIX12

Availability: out of stock



EUR 94,00






 

Details

The DAIX12 is both a dimming actuator and an interface equipped with a 230 V input. This module must be fitted in junction or distribution boxes and can be used in combination with: Wall sockets, Retractive switches with one or two normally open contacts. The DAIX12 can be used for easy automation of lighting circuits so that they can be switched or dimmed remotely or manually.

Specs

  • Rated voltage : 230 Vac, 50 Hz
  • Output :
    • 250 W bulbs
    • 200 VA Halogen lighting with wound transformer
    • 250 VA Halogen lighting with leading edge electronic transformer
  • Cartridge fuse : Radial lead micro fuse, 1.6 AT,
    according to IEC 60127-3, standard sheet 4
  • Current consumption : < 30 mA capacitive
  • Signal transmission : > 5 Vpp in 5 Ohm at 120 kHz
    in accordance with EN 50065-1, EN 50065-2-1, EN 50065-4-1
  • Transmission synchronization : 1 pulse burst at 0°/180°
  • Signal sensitivity : 25 mVpp…6 Vpp at 120 kHz ± 4 kHz
  • Signal/noise ratio : 1,35 : 1
  • Connection range : Up to 2.5 mm2, tightening torque 0.5 Nm
  • Minimum ambient temperature : 0 °C
  • Maximum ambient temperature : 40 °C
  • Atmospheric pressure : 86 hpA - 106 hpA
  • Relative humidity (non condensing) : 30 tot 90%

FAQ

Contacts

 
09794-A10-IMX10


Haibrain 09794 IMX10 Multi-function Interface (A10 XanuraHome)

XanuraHome Micro Module.
  • Four potential-free inputs.
  • A maximum of four freely programmable addresses (A1 to P16) and functions can be programmed independently of one another.
  • Can send ON/OFF, DIM/BRIGHT group commands (All Lights On, All Lights Off, All Units Off).
  • Automatic status change or fixed mode.
  • Status can be requested after commands have been sent.
  • Can be programmed remotely.

Item #: 09794-A10-IMX10

Availability: out of stock



EUR 84,96






 

Details

The IMX10 is a multi-function interface module equipped with four potential-free inputs. This module must be installed in junction boxes and can be connected to switches or retractive switches.
Application of the IMX10 makes it possible to operate lighting circuits (or appliances) fitted with switch or dimming actuators via the lighting circuit. A desired function and address can be programmed per input that can then be sent manually via the connected switch or retractive switch. To operate individual, or groups of wall sockets and lighting circuits, as control point for mechanical ventilation or as control point for starting programmed macros in, for example, a CM15Pro programmable computer interface.

Specs

  • Rated voltage : 230 Vac, 50 Hz
  • Current consumption : < 30 mA capacitive
  • Signal transmission : > 5 Vpp in 5 Ohm at 120 kHz
    in accordance with EN 50065-1, EN 50065-2-1, EN 50065-4-1
  • Transmission synchronization : 1 pulse burst at 0°/180°
  • Signal sensitivity : 25 mVpp…6 Vpp at 120 kHz ± 4 kHz
  • Signal/noise ratio : 1,35 : 1
  • Connection range : Up to 2.5 mm2, tightening torque 0.5 Nm
  • Minimum ambient temperature : 0 °C
  • Maximum ambient temperature : 40 °C
  • Atmospheric pressure : 86 hpA - 106 hpA
  • Relative humidity (non condensing) : 30 tot 90%

FAQ

Contacts

 
09779-A10-ZAX12


Haibrain 09779 ZAX12 Sun Blind Actuator (A10 XanuraHome)

XanuraHome Micro Module.
  • Four 230 V inputs.
  • Maximum load 2.5 A, 230 VAC (motors).
  • Freely programmable address for operation of the motor.
  • Freely programmable Preset address.
  • Block all operation temporarily.
  • Responds to ON/OFF/BRIGHT/DIM and EXTENDED commands.
  • Can be programmed remotely.

Item #: 09779-A10-ZAX12

Availability: out of stock. Replaced by SWM1P.



EUR 104,70






 

Details

The ZAX12 is a sun blind actuator with interface equipped with 230 V inputs. The ZAX12 can be used for easy automation of electrically operated sun blinds, roll-down shutters, curtains and screens based on 230 V motors. As a result, these applications can be operated remotely as well as manually.
Besides inputs for the Up/Down operation, the ZAX12 has a Preset input that can be programmed on a free address and an input (Lock) for (temporary) blocking of all operations. The Preset input can be used, for example, to set a sun blind or screen to a programmed preference position with one press of the button. This function also makes it possible to set several sun blinds, screens or roll-down shutters in the same position all at once without additional interfaces.

Specs

  • Rated voltage : 230 Vac, 50 Hz
  • Contact rating 230 Vac 2.5 A
  • Protection : Continuous operation time: maximum of 4 minutes. Temperature protection output.
  • Total power consumption : < 1 W Cartridge fuse
  • Radial lead micro fuse, 4 AT, according to IEC 60127-3, standard sheet 4
  • Current consumption : < 30 mA capacitive
  • Signal transmission : > 5 Vpp in 5 Ohm at 120 kHz
    in accordance with EN 50065-1, EN 50065-2-1, EN 50065-4-1
  • Transmission synchronization : 1 pulse burst at 0°/180°
  • Signal sensitivity : 25 mVpp…6 Vpp at 120 kHz ± 4 kHz
  • Signal/noise ratio : 1,35 : 1
  • Connection range : Up to 2.5 mm2, tightening torque 0.5 Nm
  • Minimum ambient temperature : 0 °C
  • Maximum ambient temperature : 40 °C
  • Atmospheric pressure : 86 hpA - 106 hpA
  • Relative humidity (non condensing) : 30 tot 90%

FAQ

Contacts

 
01807530-A10-SFX40


Haibrain 01807530 SFX40 Blocking filter (A10 XanuraHome)

Suppression filter DIN modular component.
  • Filters Haibrain® X10 commands, noise and other signals from the lighting circuit.
  • One blocking filter is needed per phase
  • Rated current 40 A
  • Central filter frequency 120 kHz
  • The suppression filter is short-circuit proof up to 10 kA and must be protected by a maximum 40 A automatic fuse with D characteristic or a 35 A fuse link.

Item #: 01807530-A10-SFX40

Availability: out of stock



EUR 135,00






 

Details

Suppression filter DIN modular component.

Model: 1807530

The SFX40 of Haibrain® is a Suppression filter that prevents Haibrain® X10 commands from leaving the house or other signals from entering the house via the lighting circuit.

In addition, the SFX40 can be used if heavy machinery causes noise on your mains. These machines electrical properties may have a dampening effect on the X10 signals. If the operation of Haibrain® X10 is affected, the suppression filter can be installed between the lighting network and the machine to prevent dampening of the signal.

The DIN rail blocking filter is modular and is installed in the distribution box.

Suppression filters can be installed immediately behind the main switch of the installation. To connect a suppression filter, phase (L) and neutral (N) need to be available, see diagram 1.

Suppression filter - Diagram 1

If the building houses heavy machinery, for example, their electrical properties may have a dampening effect on the Haibrain® X-10 signals. If the operation of Haibrain® X-10 is affected, the suppression filter can be installed between the lighting network and the machine to prevent dampening of the signal, see diagram 2.

Suppression filter - Diagram 2

Specs

TECHNICAL DATA
  • Supply voltage 230 V, 50 Hz
  • Maximum current 40 A

FAQ

Scan the QR code
of this product:
QR code

Contacts

 
01807558-A10-SAX15


Haibrain 01807558 SAX15 X10 Potential Free Actuator (A10 XanuraHome)

XanuraHome Micro Module.
  • Two galvanically separated potential-free inputs for transposing contact outputs on external devices into X10 lighting network commands.
  • One galvanically separated potential-free relay contact output for transposing X10 lighting network signals for opening and/or closing of a relay contact.
  • Lighting network connection via 2 screw terminals: phase and neutral
  • Galvanically separated relay contact with 2 screw terminals: normally open contact.
  • Galvanically separated connections by 3 wires: 2 inputs and 1 common.
  • The inputs should be secondary fed by the external equipment
  • On one side, the module can be connected directly to the mains and on the other side, via the built-in galvanic separation, to peripheral equipment to send 2 addresses and receive 1 address.
  • The module can be connected to other equipment such as a 24 V heating system (boiler), door-bell (max 24 Vac), burglar alarm system (e.g. 12 Vdc) or other equipment to make this equipment suitable for use with the Haibrain® X10.

Item #: 01807558-A10-SAX15

Availability: out of stock



EUR 69,99






 

Details

The SAX15 from Haibrain® can transpose two galvanically separated contact inputs into X10 addresses, plus on/off commands. The addresses are defined by the programmed send address of the module. The inputs are activated by an external DC or AC voltage of 5 V to 25 V. The SAX15 is in DC mode by default.

In addition the SAX15 can also transpose a received X10 address plus command to open or close the relay contact. This output is suitable for 5A AC or DC. The X10 address the unit responds to is defined during the programming of the SAX15. To do so the module needs to be provided with a receive address. The relay contact is also galvanically separated from the input wires. (max. 30 Vac/dc).

Specs

TECHNICAL DATA
Nominal supply voltage 230 V, 50Hz
Current consumption < 35 mA
Input voltage isolation 3 kV
Clearance and creepage distance prim/sec. > 5 mm
Input 1 (Brown) Binary (high: V+; low: < +1 V)
Input 2 (Red) Binary (high: V+; low: < +1 V)
Common (Green) + 5 V … + 25 V, AC or DC
Input current < 7,5 mA
Relay contact output potential-free and galvanically separated relay contact mono stable normally open
Relay contact current < 5 A resistive
Voltage relay contact/inputs < 30 V
Standards EN 60950
Signal strength sending > 5 Vpp in 5 Ohm
Signal sensitivity 15 mVpp min, > 50 mVpp at 120 kHz
Certification CE

FAQ

Contacts

 
06004683-A10-IRIX35


Haibrain 06004683 IRIX35 Infrared Interface (A10 XanuraHome)

XanuraHome Infrared Interface.
  • Makes the Haibrain X10 system operable remotely via Infrared (IR)
  • Easy to install
  • A maximum of 16 addresses can be controlled with one IR interface
  • Can be used with many of the (programmable) remote control units (NEC protocol compatible) available on the market (e.g. Philips Pronto, logitech harmony, ...)
  • Dimensions: 120 x 80 x 30 mm
  • Color: RAL 9001

Item #: 06004683-A10-IRIX35

Availability: out of stock



EUR 138,00






 

Details

The Xanura IRIX35 is an infrared interface that converts infrared signals (IR) originating from (programmable) remote control units into Haibrain X10 commands and sends these over the lighting circuit.

The IRIX35 can be used to receive infra red-commands (IR) from XanuraHome remote controls and send them over the power line to switch or dim XanuraHome actuators.

In principle, the IRIX35 can be used in two ways:

  1. Fitted to a distribution box.
  2. Connected to a wall socket.

Specs

  • Mains voltage : 230 Vac, 50 Hz
  • Max. power consumption : <2 W
  • Ambient temperature : 0 to 40 °C
  • Infrared frequency : 38 kHz (NEC compatible protocol)
  • Protection class : Class II, Double insulated
  • Type of protection : IP 40 with installation on the wall or ceiling - IP 20 with installation on the wall.
  • Standards: IEC 60950
Housing
  • Dimension (H x W x D) : 120 x 80 x 30 mm
  • Color : RAL9001
Power cable
  • Dimension : Length 1.5 m
  • Color : White

FAQ

Contacts

 
01807557-A10-CTX35


Haibrain 01807557 CTX35 data-interface (A10 XanuraHome)

XanuraHome Surface-mounted module.
  • Galvanic separated in and output.
  • 1 input : RXD.
  • 1 output: TXD.
  • Can transmit and receive all Haibrain X-10 commands.
  • Baudrate 19200 bps.
  • ASCII-protocol.
  • Internal buffer for max 30 seconds.

Item #: 01807557-A10-CTX35

Availability: out of stock



EUR 235,00






Details

The Haibrain X-10 communication transceiver CTX35 is a power line carrier transceiver with 9600bps/19.2Kbps serial data communications. A building automation system or other IBM compatible PCs can use the CTX35 to monitor and control Haibrain X-10 or other X-10 compatible control modules. It can receive and transmit standard Haibrain X-10 and extended control protocols. Transmit commands and received data is reformatted in ASCII such as A1 ON, B3 DIM, etc. to make it more user friendly than other similar devices.

Specs

  • Supply voltage : 230 Vac, 50 Hz
  • Input current : < 50 mA
  • Signal strength sending : > 5 Vpp in 5 Ohm
  • Signal sensitivity : 15 mVpp min, > 50 mVpp at 120 kHz
  • Serial connection : 9-pin Sub D-connector

Manuals

Brochure XanuraHome A10 Brochure
Manual CTX35 Manual

Software

Software CTX35 test software v. 1.0

FAQ

Contacts

Contacts

 
Shop with confidence :
Courtesy and professionalism
Courtesy and professionalism
Professional assistance
Professional assistance
100% Secure PayPal Certified
100% Secure PayPal Certified
Fast shipping
Fast shipping
Protected by Copyscape Plagiarism Checker - Do not copy content from this page.
Back to TOP